Can glass splashbacks be cut to size

Like splashbacks made of natural stone, glass splashbacks require an additional level of kitchen design planning. That’s because the glass needs to be cut to size before it’s toughened. Once this is done, the entire piece cannot be cut or processed in any way.

What is the maximum panel size for a glass splash back?

The maximum panel length for glass splashbacks is 3000mm (3 metres). Whilst the panels can be made longer, handling and installation can be challenging. This will be discussed during the measurement of your splash back.

Are glass splashbacks outdated?

While glass splashbacks have been a popular choice in past years, this is one trend that you won’t see in kitchens in 2018. In fact, even expert designers have confirmed this to be true. … He says, “We don’t do many glass splashes these days. It’s just really dated, too glossy, and doesn’t fit with contemporary trends.”

How long can a glass splashback be without a join?

A common question that we get asked regarding custom glass splashbacks is; the maximum length that we can go. A large number of our customers want a splashback that is free of glass joins, and rightfully so. The maximum length that we can go in one panel is 3.6 meters.

Can a Splashback be cut?

If you need to cut your splashback, use a fine-toothed blade that’s suitable for plastics or aluminium and make sure it’s sharp so as not to melt or chip your acrylic. A router is the best tool to use but circular or table saw can also be used providing the blade is suited to plastics.

👉 For more insights, check out this resource.

Do glass splashbacks need to be toughened?

The most common reason why your glass splashback may crack is the quality. Splashbacks that are fitted behind the hob need to be created with toughened glass. Toughened glass can withstand up to 400 ºC or several times the heat that non toughened glass can handle.

What is glass splashbacks?

Glass splashbacks are typically 6mm toughened safety glass, which adheres to all Australian building standards. Either clear glass is used, which has a natural green tint, which is good for strong dark colours or Starphire glass, which is a low iron glass.

👉 Discover more in this in-depth guide.

Can you use a normal mirror as a splashback?

The quick answer to that is yes, toughened mirror splashbacks are very heat resistant and suitable for use behind any type of kitchen hob. Normal mirror, that is not made from toughened glass, is not and could crack at any time while cooking so we would advise against a normal mirror behind a heat source.

How thick are splash backs?

Safe. Glass splashbacks typically come as a minimum 6mm thick toughened glass to comply with Australian Standards (AS2208 – Safety glazing materials for use in buildings) for safety, so that they won’t shatter when hit by something.

How do you remove a glass splashback without breaking it?

1. Cut through the silicone sealant, corner to middle. Use your wire cheese cutter to slice through the silicone sealant that attaches the splashback to the wall. …
2. Repeat the process for the other side. …
3. Slowly level the glass off the wall.

Article first time published on

How do you update glass splashbacks?

Tiles and glass – wall and splashback Thoroughly clean surface using Selleys Rapid Mould Killer. Remove all silicone sealant from joints on all surfaces using Selleys® Silicone Remover. Wash down well with water. Sand in all areas where silicone has been removed with p400 paper.

What type of splashback is best for kitchen?

What is the best kitchen splashback? Tiles are the typical choice for kitchen splashbacks. Patterned tiles are perfect for a country-style kitchen, while hexagon shaped tiles can create a cool honey-comb effect in modern kitchens. But tiles aren’t the only option when it comes to splashbacks.

Can I cut acrylic splashback?

Acrylic is also a very easy material to saw and cut, so if you need to take off more than a couple of millimetres you can always bring it to the size you want with a fine tooth saw or hacksaw.

Are acrylic splashbacks any good?

While glass has a luxury finish, acrylic splashbacks are the best option for those on a budget. They still look high-end but are a much more affordable material. Fitting a bathroom can be expensive; consider acrylic bathroom panels if you’re hoping to cut costs without compromising style and quality.

How thick is kitchen splashback glass?

A: Splashback thickness is usually 6mm, but we can do other thicknesses e.g. 8mm. Q: Can you see through the splashback glass? A: The glass is back-painted so you cannot see through to the wall or the adhesive. So unlike stained glass, it is a completely opaque finish.

Are glass splashbacks expensive?

To answer the question, are glass splashbacks cheaper than tiles, the answer is both yes and no. … A single wall of glass to under cabinet height will in most cases work out a little more expensive than lower end kitchen wall tiles but for full kitchen the cost is comparable (again depending on the wall tiles chosen).

What are glass splashbacks made of?

Glass splashbacks are usually made from float glass (or low-iron glass, if a clearer, less greenish glass is what’s needed).

Can you paint glass kitchen splashback?

We recommend that you paint the glass with 4 coats. Why you ask? 4 layers will make your splashback a light blocker. No light shall pass the glass after you paint it.

Can Splashbacks be put over tiles?

Splashbacks can be installed over existing tiles, providing they’re securely attached to the wall and there are no cracks or broken tiles which might impact the adhesion of the panel. … Any exposed tile edges can then be finished with silicone or finishing trims.

Can you put glass kitchen splashbacks over tiles?

You can install a simple glass splashback on top of tiles in a matter of minutes using neutral cure silicone, see below for a great example of a glass splashback that has been fitted on top of existing wall tiles.

Are glass splashbacks tempered?

Since severe impact or high heat can break untreated glass into dangerous, jagged shards, glass splashbacks for kitchens are made from toughened glass. Also known as “tempering,” toughening is the term for a process of intense glass heating and rapid cooling.

What is the minimum height required for a kitchen splashback?

Practically, you also need to take into account the height of the splashback. The minimum splashback height is 450mm from the bench surface. If you are installing with an electric cooktop in mind, then the minimum height of the rangehood above an electric cooktop is 600mm (as is the height of wall unit cabinets).

Can you put acrylic splashback behind cooker?

Acrylic splashbacks can be used behind cookers. The distance between the outer edge of a ceramic hob and the wall must be at least 60mm. The distance for gas hobs must be atleast 200mm.

Can you use acrylic splashback behind stove?

You can install coloured glass splashbacks directly behind Electric, Induction or Ceramic cooktops. Use behind gas cooktops with the use of a minimum 150mm non-combustible material (using our glass inserts or stainless steel) the width of your cooktop.

Are mirror splashbacks still in fashion?

They’re timeless Unlike funky finishes like subway tiles, a mirrored splashback will never be out of fashion. They blend seamlessly with your benches and cupboards, whilst making them stand out with extra reflection and light. They can be used anywhere in the kitchen without looking out of place.

Is mirror splashback expensive?

Mirrored glass splashbacks are a safety glass treated in the same way as toughened glass splashbacks, so they are an excellent choice for kitchens and safe for use behind your cooktop. COST: A mirrored glass splashback will cost you around $450 per square metre, including installation.

What is mirror splashback?

A mirror splashback is a reflective glass splashback (it looks just like a normal mirror) that is suitable for using in kitchens and other wet areas. Mirror splashbacks are made from toughened safety glass with a special mirror backing.

How much does it cost to change a splashback?

You can expect to pay anywhere from $450 to $900 for kitchen splashback installation cost, depending on the complexity of your job and the number of cut-outs you splashback requires. Cut-outs are mainly for power points and will cost anywhere from $50 each or more depending on the material.

Can you cover a glass splashback?

Vinyl wallpaper is suitable for kitchen use. Otherwise you could cover the glass with tile paint – apply it with a small roller.

Can you change the colour of a glass splashback?

Back-painted glass splashbacks can be produced in a huge range of colours that can be chosen to work with the rest of your colour scheme. … If you change your mind on the colour later on, you can simply remove and replace the glass splashback with another one.

Can you change kitchen splashback?

Change your splashback Much like the cupboard doors, changing the colour or material of your splashback can have an incredible lifting effect on the whole kitchen, especially if it has a prominent place in the kitchen.